/*
 * main3.txt 27/06/2024 11:26:23
 *
 * MAIN Generated Driver File
 * 
 * @file main.c
 * 
 * @defgroup main MAIN
 * 
 * @brief This is the generated driver implementation file for the MAIN driver.
 *
 * @version MAIN Driver Version 1.0.0
*/

/*
© [2023] Microchip Technology Inc. and its subsidiaries.

    Subject to your compliance with these terms, you may use Microchip 
    software and any derivatives exclusively with Microchip products. 
    You are responsible for complying with 3rd party license terms  
    applicable to your use of 3rd party software (including open source  
    software) that may accompany Microchip software. SOFTWARE IS ?AS IS.? 
    NO WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY, APPLY TO THIS 
    SOFTWARE, INCLUDING ANY IMPLIED WARRANTIES OF NON-INFRINGEMENT,  
    MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT 
    WILL MICROCHIP BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, 
    INCIDENTAL OR CONSEQUENTIAL LOSS, DAMAGE, COST OR EXPENSE OF ANY 
    KIND WHATSOEVER RELATED TO THE SOFTWARE, HOWEVER CAUSED, EVEN IF 
    MICROCHIP HAS BEEN ADVISED OF THE POSSIBILITY OR THE DAMAGES ARE 
    FORESEEABLE. TO THE FULLEST EXTENT ALLOWED BY LAW, MICROCHIP?S 
    TOTAL LIABILITY ON ALL CLAIMS RELATED TO THE SOFTWARE WILL NOT 
    EXCEED AMOUNT OF FEES, IF ANY, YOU PAID DIRECTLY TO MICROCHIP FOR 
    THIS SOFTWARE.
*/
#include "mcc_generated_files/system/system.h"

#include <stdbool.h>
/*
    Main application
*/

// Set the corresponding bit in var
#define  setbit(var, bit)    ((var) |= (1 << (bit)))
 
// Clear the corresponding bit in var
#define  clrbit(var, bit)    ((var) &= ~(1 << (bit)))
 
// Check to see if bit number ?bit?, in the integer ?var? is set
#define  testbit(var, bit)    ((var) & (1 <<(bit)))


int down_arrow=0; //RB0 input
int probe_temperature=0;  //RB2 analog input
long pan_temperature=0; //RB3 analog input
int motor_current=0; //RB2 analog input
int buzzer=0; //RB4 output
int spin_reset=0;//RB5 output

int up_arrow=0; //RA5 input
int time_temp=0; //RA6 input
int pwm_motor_out=0; //RA7 pwm out

int timer1=0;
int timer2=0;

char digit[4]; //RC0-RC3 each led display digit
int bcd[4];  //RA0-RA3 binary coded output to CD4511
char colon=0; //RA4 colon on the LED display
int i,patj;
int tick_count=0;
int bcdResult = 0;
int binaryInput = 0; 
int shift = 0;
char units=0;
int time_up=0;
int pat1;
int pat2;
int pat3;
int pat4;
int pat5;
int seconds=0;
int minutes=0;
int hours=0;
int tempSetpoint=150;
int timeSetpoint=0;
int buttonSelect=0;
int oneTime=0;
int debounce;
int PanTempSetpoint = 150;
int ProbeTempSetpoint=150;
int TimeSetpoint = 0;
int UpArrow=0;
int DownArrow=0;
int oneTime2=0;
int oneTime1=0;
int SetpointSelect = 0;
int ThreeSecondTimer = 0;
int StartThreeSecondTimer=0;
int SetFlag=0;
int StartCook = 0;
int newOne = 0;
int CookTime = 0;
int RawPanTemperature = 0;
int FiltPanTemperature =0;
int RawProbeTemperature = 0;
int FiltProbeTemperature =0;
int myindex = 0;
char sPanTempSetpoint[8];
char sProbeTempSetpoint[8];

// NTC thermistor resistance table
// Temperature (degrees F) Resistance (kOhms)
int ntc_table[][2] = {
  {59, 14},  
  {122, 61},
  {167, 134},
  {212, 252},
  {230,309},
  {257, 399},
  {266,430},
  {302, 549},
  {320,604},
  {347, 679},
  {356,700},
  {392, 777},
  {401,822},
  {437,848},
  {446,859},
  {482, 897},
};

int pat5;
int pat6;
int pat7;
int pat8;

//declaration to allow individual access to bits within a variable
union both 
{
    unsigned char byte;
    struct
    {
        unsigned b0:1, b1:1, b2:1, b3:1, b4:1, b5:1, b6:1, b7:1, b8:1,b9:1,b10:1;
    } bitv;
} var;

#include <stdio.h>


void timeBinary2bcd(int minutes, int seconds)
{
    IO_RA4_SetHigh();//turn on Colon
    
    bcdResult = 0;
    shift = 0;
    while (seconds > 0){
      bcdResult |= (seconds % 10) << (shift++ << 2);
      seconds /= 10;
    }
 bcd[0]=(bcdResult & 0x000F); //units
 bcd[1]=(bcdResult & 0x00F0) >> 4; //tens
 
    bcdResult = 0;
    shift = 0;
    while (minutes > 0) {
      bcdResult |= (minutes % 10) << (shift++ << 2);
      minutes /= 10;
    } 
 bcd[2]=(bcdResult & 0x000F); //hundreds
 bcd[3]=(bcdResult & 0x00F0) >> 4; //thousands 
IO_RA4_SetHigh();
}


//Input a binary number, and it will convert into 4 digits of BCD for use with 7 segment display driver.
void binary2bcd( int binaryInput)
{
    IO_RA4_SetLow();
    bcdResult = 0;
    shift = 0;
    while (binaryInput > 0) {
      bcdResult |= (binaryInput % 10) << (shift++ << 2);
      binaryInput /= 10;
    }
 bcd[0]=bcdResult & 0x000F; //units
 bcd[1]=(bcdResult & 0x00F0) >> 4; //tens
 bcd[2]=(bcdResult & 0x0F00) >> 8; //hundreds
 bcd[3]=(bcdResult & 0xF000) >> 12; //thousands 
}

//Used to write BCD to the CD4511 and ultimately to the TDGC 1060M
void write2display()
{ 
   IO_RA4_SetLow(); 
 //Display digits Port Pins
    //Port C3 Units
    //Port C2 Tens
    //Port C1 Hundreds    
    //Port C0 thousands
// Bin to BDC function output  
    //BCD[0] Units
    //BCD[1] Tens
    //BCD[2] Hundreds
    //BCD[3] Thousands

//set all display digit select bits low   
    IO_RC0_SetHigh();   
    IO_RC1_SetHigh();
    IO_RC2_SetHigh();
    IO_RC3_SetHigh(); 
//set all CD4511 inputs low   
   
    IO_RC0_SetHigh();   
    IO_RA0_SetLow();
    IO_RA1_SetLow();
    IO_RA2_SetLow();
    IO_RA3_SetLow();
    
//select thousands on display Associated with BCD[3]
    IO_RC0_SetLow();     
    if(testbit(bcd[3],0)!=0)PORTAbits.RA3=1;
    if(testbit(bcd[3],1)!=0)PORTAbits.RA2=1;    
    if(testbit(bcd[3],2)!=0)PORTAbits.RA1=1;    
    if(testbit(bcd[3],3)!=0)PORTAbits.RA0=1;

    __delay_ms(2);
    IO_RC0_SetHigh();
    IO_RA0_SetLow();
    IO_RA1_SetLow();
    IO_RA2_SetLow();
    IO_RA3_SetLow();
    
//select hundreds on display Associated with BCD[2]
    IO_RC1_SetLow();
    if(testbit(bcd[2],0)!=0)IO_RA3_SetHigh();
    if(testbit(bcd[2],1)!=0)IO_RA2_SetHigh();
    if(testbit(bcd[2],2)!=0)IO_RA1_SetHigh();    
    if(testbit(bcd[2],3)!=0)IO_RA0_SetHigh();

    __delay_ms(2);
    IO_RC1_SetHigh(); 
    IO_RA0_SetLow();
    IO_RA1_SetLow();
    IO_RA2_SetLow();
    IO_RA3_SetLow();
    
//select Tens on display Associated with BCD[1]
    IO_RC2_SetLow();
    if(testbit(bcd[1],0)!=0)IO_RA3_SetHigh();
    if(testbit(bcd[1],1)!=0)IO_RA2_SetHigh();
    if(testbit(bcd[1],2)!=0)IO_RA1_SetHigh();    
    if(testbit(bcd[1],3)!=0)IO_RA0_SetHigh();

    __delay_ms(2);
    IO_RC2_SetHigh();
    IO_RA0_SetLow();
    IO_RA1_SetLow();
    IO_RA2_SetLow();
    IO_RA3_SetLow();

//select units on display Associated with BCD[0]
    IO_RC3_SetLow(); 
    if(testbit(bcd[0],0)!=0)IO_RA3_SetHigh();
    if(testbit(bcd[0],1)!=0)IO_RA2_SetHigh();
    if(testbit(bcd[0],2)!=0)IO_RA1_SetHigh();    
    if(testbit(bcd[0],3)!=0)IO_RA0_SetHigh(); 
    __delay_ms(2);
    IO_RC3_SetHigh();
    
}

void SelectButton()
{
     if(IO_RB0_GetValue()==0  && oneTime)
        {
        debounce++;

        if (debounce>=1000)debounce=0;
        if(IO_RB0_GetValue()==0)
            {
            buttonSelect++;
            if(buttonSelect > 2)buttonSelect=0;
            oneTime=0;
            }
        }
    switch(buttonSelect)
        {
            case 0x00:
                IO_RA4_SetHigh();//set colon for clock

                if(UpArrow || DownArrow)
                    {    
                    SetFlag=1;
                    StartThreeSecondTimer=1;
                    SetpointSelect=0;
                    }
                if(SetFlag & (ThreeSecondTimer==0))
                    {
                    if(UpArrow)TimeSetpoint++;
                    UpArrow=0;
                    if(DownArrow)TimeSetpoint--;
                    DownArrow=0;
                    if(TimeSetpoint>=3600)TimeSetpoint=3600;
                    if(TimeSetpoint<=0)TimeSetpoint=0;
                    seconds=0;
                    DownArrow=0;
                    CookTime=TimeSetpoint*60;
                    binaryInput = TimeSetpoint;
                    timeBinary2bcd(TimeSetpoint,seconds);
                    write2display();
                    pat1=1;
                    }
                else
                    {
                    StartCook=1;
                    minutes=CookTime/60;
                    seconds=CookTime%60;
                    binaryInput = CookTime;
                    timeBinary2bcd(minutes,seconds);
                    StartThreeSecondTimer=0;
                    SetFlag=0;
                    ThreeSecondTimer=0;
                    SetpointSelect =0;
                    }

                pat1=1;
                break;
            case 0x01:
                IO_RA4_SetLow();//remove colon for clock
                

                if(UpArrow || DownArrow)
                    {    
                    SetFlag=1;
                    StartThreeSecondTimer=1;
                    SetpointSelect=0;
                    }
                if(SetFlag & (ThreeSecondTimer==0))
                    {
                    if(UpArrow)PanTempSetpoint++;
                    UpArrow=0;
                    if(DownArrow)PanTempSetpoint--;
                    if(PanTempSetpoint>=450)PanTempSetpoint=450;
                    DownArrow=0;
                    if(PanTempSetpoint>=450)PanTempSetpoint=450;               
                    binaryInput = PanTempSetpoint;
                    binary2bcd(binaryInput);
                    write2display();

                    }
                else
                    {
                    binaryInput = pan_temperature;
                    binary2bcd(binaryInput);
                    StartThreeSecondTimer=0;
                    SetFlag=0;
                    ThreeSecondTimer=0;
                    SetpointSelect =0;
                    }
                pat1=2;
                break;
            case 0x02:
                IO_RA4_SetLow();//remove colon for clock
                
                
            if(UpArrow || DownArrow)
                    {    
                    SetFlag=1;
                    StartThreeSecondTimer=1;
                    SetpointSelect=0;
                    }
                if(SetFlag & (ThreeSecondTimer==0))
                    {
                    if(UpArrow)ProbeTempSetpoint++;
                    UpArrow=0;
                    if(DownArrow)ProbeTempSetpoint--;
                    if(ProbeTempSetpoint>=450)ProbeTempSetpoint=450;
                    DownArrow=0;
                    if(ProbeTempSetpoint>=450)ProbeTempSetpoint=450;               
                    binaryInput = ProbeTempSetpoint;
                    binary2bcd(binaryInput);
                    write2display();

                    }
                else
                    {
                    binaryInput = probe_temperature;
                    binary2bcd(binaryInput);
                    StartThreeSecondTimer=0;
                    SetFlag=0;
                    ThreeSecondTimer=0;
                    SetpointSelect =0;
                    }    
                 
                pat1=3;
                break;
         }
         if(IO_RB0_GetValue()==1)oneTime=1;   
}
void IncDecButton()
{
if(IO_RA6_GetValue()==0  && oneTime1)//up arrow
        {
        debounce++;

        if (debounce>=1000)debounce=0;
        if(IO_RA6_GetValue()==0)
            {
            UpArrow=1;
            oneTime1=0;
            }
        }
if(IO_RA6_GetValue()==1)
    {
    oneTime1=1;
    UpArrow=0;
    }
//------------------------------------------------------------------
if(IO_RA5_GetValue()==0  && oneTime2)//Down arrow
        {
        debounce++;

        if (debounce>=1000)debounce=0;
        if(IO_RA5_GetValue()==0)
            {
            DownArrow=1;
            oneTime2=0;
            }
        }
if(IO_RA5_GetValue()==1)
    {
    oneTime2=1;
    DownArrow=0;
    }
}

long pan_ntc_temperature(int resistance)
{
  // Find the two table entries that bracket the resistance
  int index = 0;
  myindex=0;
 
  while(ntc_table[myindex][1] < resistance) 
  {     
    myindex++;  
//    if(myindex >= 13)myindex=13;
    pat1=1;
  } 
  // Calculate the temperature using linear interpolation  
  if(resistance <= ntc_table[14][1]){
 pan_temperature = ntc_table[myindex][0] + (resistance - ntc_table[myindex][1]) * (ntc_table[myindex + 1][0] - ntc_table[myindex][0]) / (ntc_table[myindex + 1][1] - ntc_table[myindex][1]);
 pat1=1;
  }   

 }
  

long probe_ntc_temperature(int resistance)
{
  // Find the two table entries that bracket the resistance
//  int index = 0;
  myindex=0;
  while(ntc_table[myindex][1] <  resistance)
  {
    myindex++;
//    if(myindex >= 13)myindex=13;
    pat1=1;
  } 
  // Calculate the temperature using linear interpolation
  if(resistance <= ntc_table[14][1]){    
 probe_temperature = ntc_table[myindex][0] + (resistance - ntc_table[myindex][1]) * (ntc_table[myindex + 1][0] - ntc_table[myindex][0]) / (ntc_table[myindex + 1][1] - ntc_table[myindex][1]);
 pat1=1;
}
}


int main(void)
{
    SYSTEM_Initialize();
 
    // If using interrupts in PIC18 High/Low Priority Mode you need to enable the Global High and Low Interrupts 
    // If using interrupts in PIC Mid-Range Compatibility Mode you need to enable the Global and Peripheral Interrupts 
    // Use the following macros to: 

    //Enable the Global Interrupts 
    INTERRUPT_GlobalInterruptEnable(); 

    // Disable the Global Interrupts 
    //INTERRUPT_GlobalInterruptDisable(); 

    //Enable the Peripheral Interrupts 
    INTERRUPT_PeripheralInterruptEnable(); 

    // Disable the Peripheral Interrupts 
    //INTERRUPT_PeripheralInterruptDisable(); 
    Timer0_Start();
    TMR1_Start();
  
    while(1)
    {  
 //pat3=266;     
 //ntc_temperature(pat3);       
//    pan_ntc_temperature(FiltPanTemperature);
//    probe_ntc_temperature(FiltProbeTemperature);
    IO_RA4_SetHigh();//colon    
    write2display();      
    LATB4=0x01;//buzzer
    LATB5=0x01;//reset led wheel
//    SelectButton();
//    IncDecButton();
   
    time_up++;
    if(time_up >= 2)
        {
               time_up=0;
               patj++;
               SelectButton();
               IncDecButton();
//               pan_temperature = ADCC_GetSingleConversion(channel_ANB3);
//               probe_temperature = ADCC_GetSingleConversion(channel_ANB2);
               
               RawPanTemperature = ADCC_GetSingleConversion(channel_ANB3);
               FiltPanTemperature = RawPanTemperature/8 +FiltPanTemperature*7/8;
               pan_ntc_temperature(FiltPanTemperature);
               //pan_ntc_temperature(RawPanTemperature);
//               pan_temperature = pan_ntc_temperature(FiltPanTemperature);
               
               RawProbeTemperature = ADCC_GetSingleConversion(channel_ANB2);
               FiltProbeTemperature = RawProbeTemperature/8 +FiltProbeTemperature*7/8;
               probe_ntc_temperature(FiltProbeTemperature);
//               probe_temperature = probe_ntc_temperature(FiltPanTemperature);    
                 
               motor_current = ADCC_GetSingleConversion(channel_ANB1);
               PWM7_LoadDutyValue(10);
               
//             To App as String

               sprintf(sPanTempSetpoint,"%d\0",PanTempSetpoint);
               sprintf(sProbeTempSetpoint,"%d\0",ProbeTempSetpoint);
               
	           printf(sPanTempSetpoint);   
               printf(sProbeTempSetpoint);
               
               pat1=1;
        }          
         
     
    }
}